← All Guides

How to Fix Elephant Foot and First-Layer Problems on Resin Prints

Elephant foot is a bottom-layer exposure problem, not a general exposure problem. Here's how to tell it apart from adhesion failure, how to fix it with bottom exposure and transition layers, and why lifting the model off the plate solves it permanently.

This guide contains affiliate links: I may earn a small commission at no extra cost to you.

You print a batch of dungeon tiles flat on the plate. They come off, they wash, they cure, and then none of them sit flush against each other. There is a faint lip around the bottom edge of every single one, a millimetre of extra material that is not in the STL. Or you print a mini directly on the plate to save support cleanup, and its feet have spread out like they melted into the ground.

That is elephant foot, and it is the most predictable defect in resin printing because it is caused by a setting you are supposed to have turned up. This guide covers what is actually happening in those first few layers, how to separate it from the failures it gets confused with, and the two different ways to fix it depending on whether you need the model on the plate or not. If you are still early in the process, the complete beginner’s guide to resin printing miniatures covers the setup and slicing steps this guide assumes you already have working.


What Elephant Foot Actually Is

Every resin slicer profile has two exposure numbers: one for normal layers, and a much larger one for the first few layers off the build plate. Normal exposure on a monochrome LCD might be two to three seconds. Bottom exposure on the same profile is commonly twenty-five to fifty seconds.

That gap exists for one reason. The first layers have nothing to bond to except bare metal, and they have to survive every peel cycle for the rest of the print. So they get flooded with UV until they are unambiguously stuck.

The side effect is that UV does not stop neatly at the edge of the masked pixel. Light scatters sideways through the resin, and cure creeps outward from the exposed area. At normal exposure that creep is small enough to ignore. At thirty seconds it is not. Each bottom layer comes out slightly wider than the geometry that generated it, and stacked together they read as a flare.

Two things follow from that, and both matter for the fix:

The flare is only as tall as your bottom layers. If you have eight bottom layers at 0.05mm, the affected band is 0.4mm tall. It does not extend up the model, because layer nine is printed at normal exposure.

The step between the two exposures is itself a defect. Where the last over-cured bottom layer meets the first normally cured layer, there is an abrupt change in width. On a vertical surface that reads as a hard ledge, sometimes more visible than the flare underneath it.


Rule Out the Two Things It Gets Confused With

Before changing any settings, confirm you are actually looking at elephant foot. Two other problems produce distortion near the base and have completely different fixes.

General over-exposure. If normal exposure is too high, the whole model is oversized: detail is soft, recesses are filled in, and small gaps between features have closed up. The base looks bad, but so does the face. Bottom exposure is not the problem here, and cutting it will not help. Run a proper exposure test first. The resin exposure test and calibration guide walks through that with a test model, and it is genuinely the prerequisite for this one: do not tune bottom layers on top of an uncalibrated normal exposure.

Adhesion failure and its aftermath. A model that partially detached and re-stuck, or that shifted on the plate during printing, can leave a mangled base that superficially resembles a flare. The tell is that adhesion damage is irregular and often asymmetric, while elephant foot is uniform all the way around the perimeter. Plate preparation and levelling are their own topic, and they belong to first-layer adhesion, not first-layer dimension.

There is a third case worth naming: distortion partway up the model, or banding on vertical surfaces well clear of the plate. That is not a bottom-layer problem at all, and nothing in this guide will touch it. The resin print failure troubleshooting guide covers layer separation and the other nine common failure modes if the symptom does not match anything here.

The quick test: hold the model at eye level and find where the distortion stops. If it ends within half a millimetre of the surface that touched the plate, it is elephant foot. If it does not, stop reading and go diagnose something else.


Fix One: Tune the Bottom Layers

This is the fix when you need the model printed flat on the plate. Change one thing at a time, and reprint something small between each change.

Reduce bottom exposure

Cut it by 15 to 20 percent and reprint. If the flare is smaller but still there, cut again. You are hunting for the lowest bottom exposure that still holds reliably.

Where that lands depends on your resin, your plate, and your room temperature, which is why nobody can hand you a number. Manufacturers publish a starting bottom exposure on the bottle, and that figure is generally conservative on purpose: it is tuned so that a first-time user’s print does not fall off, not so that the base is dimensionally perfect. There is usually real headroom below it.

The failure mode when you go too far is unmistakable. The print detaches, either completely (empty plate, cured slab on the FEP) or partially. If that happens, go back up one step and stop.

Reduce the bottom layer count

This one is free and most people skip it. Look at how many bottom layers your profile uses. Six or eight is a common default. Every one of those is printed at the full bottom exposure.

Four is generally enough for a well-levelled plate and a supported print. Going from eight to four halves the height of the affected band before you touch exposure at all, and on a model where the flare was already marginal, that alone can put it below the level where you notice.

Do not take it to one or two. You are trading directly against adhesion, and a detached print costs more than a sanded base.

Add transition layers

Transition layers (Chitubox and Lychee both have this, sometimes labelled as a transition layer count plus a falloff type) ramp exposure down from the bottom value to the normal value over several layers instead of dropping in one step.

Set four to eight. This does not reduce the flare much, but it removes the hard ledge where the two exposure regimes meet, which is frequently the part that actually shows on a finished mini. If you have ever looked at a printed base and seen a crisp horizontal line about half a millimetre up, that is what transition layers fix.

Both slicers cover this in their own settings pages: Chitubox settings for miniatures and Lychee slicer settings for miniatures have the relevant fields.

A workable order of operations

StepChangeWhat you expect
1Calibrate normal exposure firstDetail is sharp; base still flared
2Bottom layers 8 → 4Flare band roughly half as tall
3Transition layers → 6Hard ledge disappears
4Bottom exposure −15%Flare visibly smaller
5Bottom exposure −15% againRepeat until flare is gone or adhesion drops
6Back off one step on any failureLast known-good setting

Fix Two: Stop Printing on the Plate

The tuning above manages the problem. Lifting the model off the plate eliminates it.

If nothing on the model touches the build plate, nothing on the model is printed at bottom exposure. The over-cured, flared layers all end up on the raft, and the raft goes in the bin. Elephant foot on the model becomes structurally impossible rather than merely small.

This is why almost every well-supported miniature you see on a print farm is floating a few millimetres above the plate on a raft. It is not only about peel forces and orientation; it also moves the entire bottom-layer problem onto a disposable part.

The trade is support cleanup. You get support marks somewhere on the model instead of a flare underneath it, so the real question is which surface you would rather compromise. For a miniature, marks on the underside of a cloak are easier to hide than a spread base. For a flat tile that has to tessellate, it is not even close: lift it.

Two guides cover the setup this needs: how to orient resin miniatures for choosing the angle, and how to add supports to resin miniatures for the support density and contact point sizes that survive the print without scarring the model.

When printing flat on the plate is still the right call: large flat-bottomed terrain pieces where support cleanup across the whole underside would be worse than a lip, and batch jobs where you genuinely do not care about the base because it will be glued into a rim and covered in texture paste anyway. In those cases, tune the bottom layers, accept a small flare, and move on.


Fixing a Model You Have Already Printed

You do not need to reprint to salvage a part.

Sanding. Lay a sheet of wet-and-dry paper flat on a table, wet it slightly, and move the base of the model across it in small circles with even pressure. Start at 400 grit, finish at 600 or 800 if the surface will be visible. Keeping the paper flat and moving the model (rather than holding the paper and rubbing the model) is what gets you a genuinely flat base instead of a rounded one.

Knife work. For a hard transition ledge rather than a flare, hold a sharp hobby knife perpendicular to the surface and scrape sideways along the ridge. Scraping shaves the high spot without digging in the way cutting does.

Timing matters. Green resin, meaning washed but not yet UV-cured, cuts and sands noticeably more easily than fully cured resin. If you already know a part needs cleanup, do it between the wash and the cure. If it is already cured, everything still works, it just takes longer.

Sanding cured resin produces fine dust, and cured resin dust is a respiratory irritant. Sand wet, which keeps the dust bound in the water, and wear a mask if you are doing a batch. Full handling precautions are in the resin printing safety guide; this is one of the steps people skip because the resin is already cured and it feels safe.

Basic kit for this, if you do not already have it: a wet and dry sandpaper assortment in the 400 to 1000 range, hobby knife blades (a dull blade tears resin instead of shaving it, so replace them often), and a digital caliper if you want to actually measure the flare rather than eyeball it. The caliper is the one that changes how you work: measuring the base against the STL dimension turns “that looks a bit wide” into a number you can chase.


Verify the Fix Properly

Do not test new bottom-layer settings on a full plate. Print one small object, or a single spare mini, and check three things:

  1. Look along the base at a shallow angle under a bright light. A flare that is invisible head-on shows clearly in raking light.
  2. Run a fingernail up from the base. You will feel a ledge well before you can see one.
  3. Put it on a flat surface and press one edge. A flared base rocks. A clean one does not.

If a short print comes off clean, commit the profile. If you tightened bottom exposure, keep an eye on the next few prints: adhesion margin is the thing you just spent, and a change in room temperature or a resin bottle from a different batch can push a marginal setting over the edge. Adding a quick pre-print check to your routine catches that early, which is what the pre-print checklist is for.


The Short Version

Elephant foot is over-cured bottom layers spreading sideways. It is confined to the first few tenths of a millimetre off the plate, it is uniform around the perimeter, and it is not the same problem as general over-exposure or as adhesion failure.

Calibrate normal exposure first. Then cut bottom layer count, add transition layers, and step bottom exposure down until the flare is gone or adhesion starts to go. If the surface actually matters, skip all of that and lift the model onto a raft, which moves the defect onto a part you throw away.

And if the print is already done and the base is already flared: 400 grit, wet, flat on the table. Two minutes.